
"Optical density" redirects here. "Optical density" can also refer to index of refraction.^{[1]}
In chemistry, absorbance or decadic absorbance is the common logarithm of the ratio of incident to transmitted radiant power through a material, and spectral absorbance or spectral decadic absorbance is the common logarithm of the ratio of incident to transmitted spectral radiant power through a material.^{[2]} Absorbance is dimensionless, and in particular is not a length, though it is a monotonically increasing function of path length, and approaches zero as the path length approaches zero. The use of the term "optical density" for absorbance is discouraged.^{[2]} In physics, a closely related quantity called "optical depth" is used instead of absorbance: the natural logarithm of the ratio of incident to transmitted radiant power through a material. The optical depth equals the absorbance times ln(10).
The term absorption refers to the physical process of absorbing light, while absorbance does not always measure absorption: it measures attenuation (of transmitted radiant power). Attenuation can be caused by absorption, but also reflection, scattering, and other physical processes.
Contents

Mathematical definitions 1

Absorbance 1.1

Spectral absorbance 1.2

Relationship with attenuation 2

Attenuance 2.1

Attenuation coefficient 2.2

Measurements 3

Logarithmic vs. directly proportional measurements 3.1

Instrument measurement range 3.2

Method of measurement 3.3

Shade number 4

See also 5

References 6
Mathematical definitions
Absorbance
Absorbance of a material, denoted A, is given by^{[2]}

A = \log_{10}\!\left(\frac{\Phi_\mathrm{e}^\mathrm{i}}{\Phi_\mathrm{e}^\mathrm{t}}\right) = \log_{10} T,
where

Φ_{e}^{t} is the radiant flux transmitted by that material;

Φ_{e}^{i} is the radiant flux received by that material;

T is the transmittance of that material.
Absorbance is related to optical depth by

A = \frac{\tau}{\ln 10},
where τ is the optical depth.
Spectral absorbance
Spectral absorbance in frequency and spectral absorbance in wavelength of a material, denoted A_{ν} and A_{λ} respectively, are given by^{[2]}

A_\nu = \log_{10}\!\left(\frac{\Phi_{\mathrm{e},\nu}^\mathrm{i}}{\Phi_{\mathrm{e},\nu}^\mathrm{t}}\right) = \log_{10} T_\nu,

A_\lambda = \log_{10}\!\left(\frac{\Phi_{\mathrm{e},\lambda}^\mathrm{i}}{\Phi_{\mathrm{e},\lambda}^\mathrm{t}}\right) = \log_{10} T_\lambda,
where
Spectral absorbance is related to spectral optical depth by

A_\nu = \frac{\tau_\nu}{\ln 10},

A_\lambda = \frac{\tau_\lambda}{\ln 10},
where

τ_{ν} is the spectral optical depth in frequency;

τ_{λ} is the spectral optical depth in wavelength.
Although absorbance is properly unitless, it is sometimes reported in "absorbance units", or AU. Many people, including scientific researchers, wrongly state the results from absorbance measurement experiments in terms of these madeup units.^{[3]}
Relationship with attenuation
Attenuance
Absorbance is a number that measures the attenuation of the transmitted radiant power in a material. Attenuation can be caused by the physical process of "absorption", but also reflection, scattering, and other physical processes. Absorbance of a material is approximately equal to its attenuance when both the absorbance is much less than 1 and the emittance of that material (not to be confused with radiant exitance or emissivity) is much less than the absorbance:

\Phi_\mathrm{e}^\mathrm{t} + \Phi_\mathrm{e}^\mathrm{att} = \Phi_\mathrm{e}^\mathrm{i} + \Phi_\mathrm{e}^\mathrm{e},

T + ATT = 1 + E,
where

Φ_{e}^{t} is the radiant power transmitted by that material;

Φ_{e}^{att} is the radiant power attenuated by that material;

Φ_{e}^{i} is the radiant power received by that material;

Φ_{e}^{e} is the radiant power emitted by that material;

T = Φ_{e}^{t}/Φ_{e}^{i} is the transmittance of that material;

ATT = Φ_{e}^{att}/Φ_{e}^{i} is the attenuance of that material;

E = Φ_{e}^{e}/Φ_{e}^{i} is the emittance of that material,
and according to Beer–Lambert law,

T = 10^{A},
so:

ATT = 1  10^{A} + E \approx A + E \approx A,\quad \text{if}\ A \ll 1\ \text{and}\ E \ll A.
Attenuation coefficient
Absorbance of a material is also related to its decadic attenuation coefficient by

A = \int_0^l a(z)\, \mathrm{d}z,
where

l is the thickness of that material through which the light travels;

a(z) is the decadic attenuation coefficient of that material at z,
and if a(z) is uniform along the path, the attenuation is said to be a linear attenuation and the relation becomes:

A = al.
Sometimes the relation is given using the molar attenuation coefficient of the material, that is its attenuation coefficient divided by its molar concentration:

A = \int_0^l \varepsilon c(z)\, \mathrm{d}z,
where

ε is the molar attenuation coefficient of that material;

c(z) is the molar concentration of that material at z,
and if c(z) is uniform along the path, the relation becomes:

A = \varepsilon cl.
The use of the term "molar absorptivity" for molar attenuation coefficient is discouraged.^{[2]}
Measurements
Logarithmic vs. directly proportional measurements
The amount of light transmitted through a material diminishes exponentially as it travels through the material, according to Beer–Lambert law. Since the absorbance of a sample is measured as a logarithm, it is directly proportional to the thickness of the sample and to the concentration of the absorbing material in the sample. Some other measures related to absorption, such as transmittance, are measured as a simple ratio so they vary exponentially with the thickness and concentration of the material.
Absorbance: −log_{10}(Φ_{e}^{t}/Φ_{e}^{i})

Transmittance: Φ_{e}^{t}/Φ_{e}^{i}

0

1

0.1

0.79

0.25

0.56

0.5

0.32

0.75

0.18

0.9

0.13

1

0.1

2

0.01

3

0.001

Instrument measurement range
Any real measuring instrument has a limited range over which it can accurately measure absorbance. An instrument must be calibrated and checked against known standards if the readings are to be trusted. Many instruments will become nonlinear (fail to follow the Beer–Lambert law) starting at approximately 2 AU (~1% transmission). It is also difficult to accurately measure very small absorbance values (below 10^{−4}) with commercially available instruments for chemical analysis. In such cases, laserbased absorption techniques can be used, since they have demonstrated detection limits that supersede those obtained by conventional nonlaserbased instruments by many orders of magnitude (detections have been demonstrated all the way down to 5 × 10^{−13}). The theoretical best accuracy for most commercially available nonlaserbased instruments is in the range near 1 AU. The path length or concentration should then, when possible, be adjusted to achieve readings near this range.
Method of measurement
Typically, absorbance of a dissolved substance is measured using absorption spectroscopy. This involves shining a light through a solution and recording how much light and what wavelengths were transmitted onto a detector. Using this information, the wavelengths that were absorbed can be determined.^{[4]} First, measurements on a "blank" are taken using just the solvent for reference purposes. This is so that the absorbance of the solvent is known, and then any change in absorbance when measuring the whole solution is made by just the solute of interest. Then measurements of the solution are taken. The transmitted spectral radiant flux that makes it through the solution sample is measured and compared to the incident spectral radiant flux. As stated above, the spectral absorbance at a given wavelength is

A_\lambda = \log_{10}\!\left(\frac{\Phi_{\mathrm{e},\lambda}^\mathrm{i}}{\Phi_{\mathrm{e},\lambda}^\mathrm{t}}\right)\!.
The absorbance spectrum is plotted on a graph of absorbance vs. wavelength.^{[5]}
A UVVis spectrophotometer will do all this automatically. To use this machine, solutions are placed in a small cuvette and inserted into the holder. The machine is controlled through a computer and, once you "blank" it, will automatically display the absorbance plotted against wavelength. Getting the absorbance spectrum of a solution is useful for determining the concentration of that solution using the Beer–Lambert law and is used in HPLC.
Shade number
Some filters, notably welding glass, are rated by shade number, which is 7/3 times the absorbance plus one:^{[6]}

SN = \frac{7}{3}A + 1,
or

SN = \frac{7}{3}(\log_{10} T) + 1,
where SN is the shade number.
So, if the filter has 0.1% transmittance (0.001 transmittance, which is 3 absorbance units) the shade number would be 8.
See also
References

^ Zitzewitz, Paul W. (1999). Glencoe Physics. New York, N.Y.: Glencoe/McGrawHill. p. 395.

^ ^{a} ^{b} ^{c} ^{d} ^{e} IUPAC, Compendium of Chemical Terminology, 2nd ed. (the "Gold Book") (1997). Online corrected version: (2006–) "Absorbance".

^ "How to Make Your Next Paper Scientifically Effective". J. Phys. Chem. Lett. (4): 1578−1581. 2013.

^ Reusch, William. "Visible and Ultraviolet Spectroscopy". Retrieved 20141029.

^ Reusch, William. "Empirical Rules for Absorption Wavelengths of Conjugated Systems". Retrieved 20141029.

^ Russ Rowlett (20040901). "How Many? A Dictionary of Units of Measurement". Unc.edu. Retrieved 20100920.


High resolution



Medium resolution



Spectroscopic



Translational Diffusion



Rotational Diffusion



Chemical



Thermodynamic



Computational





This article was sourced from Creative Commons AttributionShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and USA.gov, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for USA.gov and content contributors is made possible from the U.S. Congress, EGovernment Act of 2002.
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a nonprofit organization.