World Library  
Flag as Inappropriate
Email this Article

Dummy load

Article Id: WHEBN0000705791
Reproduction Date:

Title: Dummy load  
Author: World Heritage Encyclopedia
Language: English
Subject: AN/ARC-190, Microwave power meter, Power supply, Radio electronics, Dummy
Collection: Radio Electronics
Publisher: World Heritage Encyclopedia

Dummy load

Large RF dummy load for shortwave transmitter at the Moosbrunn transmitting station of the Austrian Broadcasting Service, Moosbrunn, Austria. It uses a sodium hydroxide solution to absorb the radio energy, which is circulated through the radiator (center) to cool it. It has a capacity of 100 kW.

A dummy load is a device used to simulate an electrical load, usually for testing purposes. In radio a dummy antenna is connected to the output of a radio transmitter and electrically simulates an antenna, to allow the transmitter to be adjusted and tested without radiating radio waves. In audio systems a dummy load is connected to the output of an amplifier to electrically simulate a loudspeaker, allowing the amplifier to be tested without producing sound. Load banks are connected to electrical power supplies to simulate the supply's intended electrical load for testing purposes.


  • Radio 1
  • Audio 2
  • Power supplies 3
  • See also 4
  • References 5
  • Further reading 6
  • External links 7


Microwave dummy load designed to attach to waveguide.

In radio this device is also known as a dummy antenna or a radio frequency termination. It is a device used in place of an antenna to aid in testing a radio transmitter. It is substituted for the antenna while adjusting the transmitter, so that no radio waves are radiated, so that the transmitter does not interfere with other radio transmitters during the adjustments. [1] If a transmitter is tested without a load attached to its output terminals such as an antenna or a dummy load, the power will be reflected back into the transmitter, often overheating and damaging it. Also, if a transmitter is adjusted without a load, it will operate differently as compared with a load, and the adjustments may be incorrect.

The dummy load ordinarily should be a pure resistance; the amount of resistance should be the same as the impedance of the antenna or transmission line that is used with the transmitter (usually 50 Ω or 75 Ω).[2] The radio energy that is absorbed by the dummy load is converted to heat. A dummy load must be chosen or designed to tolerate the amount of power that can be delivered by the transmitter. [3]

The ideal dummy load provides a standing wave ratio (SWR) of 1:1 at the given impedance.

Veterinarian-grade mineral oil, an inexpensive source for mineral oil, is frequently used by amateur radio operators as coolant in RF dummy loads.


Four heavy duty dummy loads used at an amplifier shootout

When testing audio amplifiers, it is common to replace the loudspeaker with a dummy load, so that the amplifier's handling of large power levels can be tested without actually producing intense sound. The simplest is a resistor bank to simulate the voice coil's resistance.

For loudspeaker simulation, a more complex network is more accurate, however, as actual loudspeakers are reactive and non-linear. There are many designs for loudspeaker simulators, which emphasize different characteristics of the actual speaker, such as the voice coil's inductance, mechanical suspension compliance, and cone mass.

Power supplies

There are also dummy loads for power supplies, known as load banks. These may be used, for example, for factory and in-service testing of standby generators. A load bank may be used to stabilize a power system in case of loss of load, for example, on an isolated wind or mini-hydro plant.

An electronic load (or e-load) is a device or assembly that simulates loading on an electronic circuit. It is used as substitute for a conventional ohmic load resistor.

Electronic loads with 800W and 4200W from Höcherl & Hackl

As counterpart to a current source, the electronic load is a current sink. When loading a current source with a fixed resistor one can set one determined load current by the connected load resistor. The characteristic of the electronic load is that the load current can be set and varied in a defined range. The load current is regulated electronically.

The electronic load consumes electric energy and in most cases transforms it into heat. Fans or water-cooled elements are used as coolers. Under certain conditions, energy-recycling into the public power supply system is also possible.

Electronic loads are used in diverse applications, particularly for the test of power supplies, batteries, solar and fuel cells, generators. AC loads are used to test transformers, uninterruptible power supplies (UPS) or onboard power supplies. The equipment and power spectrum of such electronic loads begins with simplest circuits consisting in general of a potentiometer for current setting and a transistor circuit for power transforming. Further developed electronic loads supply several operating modes, in most cases constant current, voltage, power and resistance. Nowadays, the equipment may be controlled by a PLC or remotely by a PC. Settings and measured values such as input voltage and actual load current are indicated on a display.

See also


  1. ^ Kleinschmidt, Kirk, ed. (1990). ARRL Handbook for the Radio Amateur. Newington, Connecticut: American Radio Relay League. pp. 25–21 through 25–23. 
  2. ^ Kleinschmidt, Kirk, ed. (1990). ARRL Handbook for the Radio Amateur. Newington, Connecticut: American Radio Relay League. pp. 25–21. 
  3. ^ Kleinschmidt, Kirk, ed. (1990). ARRL Handbook for the Radio Amateur. Newington, Connecticut: American Radio Relay League. pp. 34–22 through 34–28. 

Further reading

  • Ausias Garrigós and José M Blanes (2005-03-17). "Power MOSFET is core of regulated-dc electronic load". EDN. 
  • Martin Rowe (2005-12-01). "Loads need calibration, too". Ensuring power supply accuracy (Test and Measurement World). 
  • M. B. Borage, S. R. Tiwari, and S. Kotaiah (2003-07-07). "Inductive electronic load for testing of magnet power supplies in particle accelerators". Review of Scientific Instruments 74 (12): 5194–5196.  
  • Meng-Yueh Chang, Jiann-Yow Lin, Shih-Liang Jung, Ying-Yu Tzou (1997-06-27). "Design and implementation of a real-time lossless dynamic electronic load simulator". 28th Annual IEEE Power Electronics Specialists Conference 1: 734–739.  
  • B. Singh, S.S. Murthy, S. Gupta (2004-01-14). "Analysis and implementation of an electronic load controller for a self-excited induction generator". Proceedings of Generation, Transmission and Distribution 131 (1): 51–60. 

External links

  • Speaker impedance -
This article was sourced from Creative Commons Attribution-ShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for and content contributors is made possible from the U.S. Congress, E-Government Act of 2002.
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a non-profit organization.

Copyright © World Library Foundation. All rights reserved. eBooks from World eBook Library are sponsored by the World Library Foundation,
a 501c(4) Member's Support Non-Profit Organization, and is NOT affiliated with any governmental agency or department.