World Library  
Flag as Inappropriate
Email this Article

Expeller pressing

Article Id: WHEBN0001880117
Reproduction Date:

Title: Expeller pressing  
Author: World Heritage Encyclopedia
Language: English
Subject: Press cake, Teli, De Zoeker, Zaandam, Pressing, High lipid content microalgae
Collection: High Lipid Content Microalgae, Liquid-Solid Separation, Oils
Publisher: World Heritage Encyclopedia

Expeller pressing

An expeller used for expeller pressing
Coconut oil is expelled from copra at an oil mill in Tripunithura, Kerala, India

Expeller pressing (also called oil pressing) is a mechanical method for extracting oil from raw materials. The raw materials are squeezed under high pressure in a single step. When used for the extraction of food oils, typical raw materials are nuts, seeds and algae, which are supplied to the press in a continuous feed. As the raw material is pressed, friction causes it to heat up; in the case of harder nuts (which require higher pressures) the material can exceed temperatures of 120 °F (49 °C).


  • Overview 1
  • Efficiency 2
  • Design 3
    • Continuous screw 3.1
    • Interrupted screw 3.2
    • Resistor teeth 3.3
  • Expanded applications 4
  • See also 5
  • References 6


An expeller press is a screw-type machine that presses oil seeds through a caged barrel-like cavity. Raw materials enter one side of the press and waste products exit the other side. The machine uses friction and continuous pressure from the screw drives to move and compress the seed material. The oil seeps through small openings that do not allow seed fiber solids to pass through. Afterward, the pressed seeds are formed into a hardened cake, which is removed from the machine. Pressure involved in expeller pressing creates heat in the range of 140–210 °F (60–99 °C). Some companies claim that they use a cooling apparatus to reduce this temperature to protect certain properties of the oils being extracted.[1]


Expeller processing cannot remove every last trace of liquid (usually oil) from the raw material. A significant amount remains trapped inside of the cake left over after pressing. In most small-scale rural situations this is of little or no importance, as the cake that remains after the oil has been removed finds uses in local dishes, in the manufacture of secondary products, or for animal feed. Some raw materials, however, do not release oil by simple expelling, the most notable being rice bran. In order to remove oil from commodities that do not respond to expelling or to extract the final traces of oil after expelling, it is necessary to use solvent extraction.


Continuous screw

The earliest expeller presses utilized a continuous screw design. The compression screws were much like the screws of a screw conveyor—that is, the helicoid flighting started at one end and ended at the other.

Interrupted screw

Valerius Anderson invented the interrupted screw design and patented it in the year 1900.[2] Anderson observed that in the continuous flighting arrangement of a compression screw, there are tendencies for slippery materials either to co-rotate with the screw or to pass through with minimal dewatering. He wrote that "brewers' slops, slaughterhouse refuse" and other "soft and mushy" materials dewater poorly in continuous screw presses.

His invention consisted of putting interruptions in the flighting of a compression screw. It was much like having a hanger bearing in a screw conveyor: there is no flighting on the shaft at that point, so material tends to stop moving and pile up. It is only after solids accumulate in the gap that the downstream flighting catches material. When this happens, material is forced along its way. The result is better dewatering and thus a more consistent press cake.

Resistor teeth

After the 1900 patent, a major improvement was made with the addition of resistor teeth. Fitted into the gaps where there is no flighting, these teeth increase the agitation within the press, further diminishing co-rotation tendencies.

Expanded applications

As the years went by, applications of the interrupted screw design were expanded beyond slippery and slimy materials. This took place because competing continuous screw presses worked best only under conditions of constant feed, at constant consistency. If either the consistency or the flow rate diminished, squeezing would diminish until it was inadequate for proper moisture removal. At the same time, if the consistency increased, the press could jam. To counteract these tendencies it was necessary to build a very heavy press, frequently with an expensive variable speed drive.

In contrast, it was found that the interruptions in the flighting of the Anderson screw would provide cushion within the press. If consistency went down, compression was still effective. A plug of sufficiently solid material had to build up at each interruption before solids could progress towards the discharge. This self-correcting performance prevents wet material from purging at the cake discharge. It is achieved without varying the speed of the screw.

The economic advantages of these characteristics led to interrupted screw presses being used to dewater fibrous materials that are neither slippery nor slimy. Examples would be alfalfa, corn husk, and, more recently, paper mill fibers.

See also


  1. ^ Spectrum Expeller Pressed vs. Cold Pressed
  2. ^ Twin screw press with interrupted flights - US Patent 6550376 Description
This article was sourced from Creative Commons Attribution-ShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for and content contributors is made possible from the U.S. Congress, E-Government Act of 2002.
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a non-profit organization.

Copyright © World Library Foundation. All rights reserved. eBooks from World eBook Library are sponsored by the World Library Foundation,
a 501c(4) Member's Support Non-Profit Organization, and is NOT affiliated with any governmental agency or department.